|
|
Renesas
|
Front-end Module, Dual Path RF Switch / LNA 2300MHz to 2700MHz, 6x6, 32-Pin |
More Info
The F0452B is an integrated dual-path RF front-end consisting of an RF switch and two gain stages with 6dB gain control used in the analog front-end receiver of an Active Antenna System (AAS). The F0452B supports frequencies from 2300MHz to 2700MHz. The F0452B provides 34dB gain with +23dBm OIP3, +15dBm output P1dB, and 1.5dB noise figure at 2600MHz. Gain is reduced 6dB in a single step with a maximum settling time of 31ns. The device uses a single 3.3V supply and 130mA of IDD. The F0452B is offered in a 5 × 5 × 0.8 mm, 32-LGA package with 50Ω input and output amplifier impedances for ease of integration into the signal path.
Specifications
- Part Number:F0452
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
490 In Stock |
|
|
|
|
Renesas
|
Amplifier, Variable Gain, 0.6 to 2.7GHz, 29.5dB max gain, +39dBm OIP3, -40 to 105'C, 7x7mm 48-LGA package |
More Info
| 1 | $16.29 | | 25 | $15.03 | | 50 | $13.96 | | 100 | $13.02 |
Dual Matched Broadband RF DVGA - 0.6GHz to 2.7GHz The F0443 is a highly integrated 0.6GHz to 2.7GHz dual channel RF digital variable gain amplifier designed for use in diversity/MIMO receivers. The F0443 provides two independent receiver paths each with 29.5dB typical maximum gain and 3.2dB NF at 2.5GHz. For each path, gain control is split into four separate digital step attenuators: DSA0 provides 6dB of attenuation in a single step using SPI/I3C control. Its counterpart, DSA1, also provides 6dB of attenuation in a single step but it is programmed instead using an external direct control pin. DSA2 yields 29dB of SPI/I3C-controlled attenuation in 1dB steps, while its counterpart, DSA3, includes 18dB attenuation in 6dB steps programmed via two external control pins. The device offers +39dBm nominal output IP3 at 2.5GHz using 372mA total ICC for two active paths with a +5V supply voltage. The F0443 is packaged in a 7 × 7 mm, 48-LGA with 50Ω single-ended RF input and RF output impedances for ease of integration into the signal path. Features - RF Frequency Range: 0.6GHz to 2.7GHz
- Gain at 2.5GHz:
- 5dB typical max gain in non-bypass mode
- 9dB typical max gain in bypass mode
- DSA Control:
- DSA0: Single 6dB step via SPI/I3C control
- DSA1: Single 6dB step via 1-bit external pin control
- DSA2: 29dB range in 1dB steps via SPI/I3C control
- DSA3: 18dB range in 6dB steps via 2-bit external pin control
- +39dBm OIP3 at 2.5GHz
- NF at 2.5GHz
- 2dB typical in non-bypass mode
- 9dB typical in bypass mode
- +19.7dBm OP1dB at 2.5GHz
- ICC = 372mA
- Standby Mode for power savings with 9mA standby current
- 50Ω single-ended input/output impedances
- 8V logic support
- Operating temperature range: -40°C to +105°C
- 7 × 7 mm 48-LGA package
Specifications
- Part Number:F0443
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
245 In Stock |
| 1 | $16.29 | | 25 | $15.03 | | 50 | $13.96 | | 100 | $13.02 |
|
|
|
|
Renesas
|
Amplifier, Variable Gain, 0.35 to 3GHz, 23.3dBm, 14.3dB gain, 4x4mm |
More Info
| 1 | $5.62 | | 10 | $5.06 | | 100 | $4.21 | | 1000+ | $3.55 |
The F1431B is a high linearity RF Digital Variable Gain Amplifier, (DVGA) used as the power amplifier driver in transmitter applications. The F1431B provides 14dB gain, +41.1dBm OIP3, and a 4.2dB noise figure (NF) at 2.0GHz. The digital step attenuator (DSA) has 23dB range with a 0.5dB step size and operates from 0.35GHz to 3GHz with one tuning circuit. This device uses a single 5V supply and 150mA of current. - 0.35GHz to 3GHz operating range
- 14.3dB typical gain at 2GHz
- Glitch-Free™ 23dB gain adjustment
- 0.5dB step size
- 4.2dB NF at 2GHz
- +41.1dBm OIP3 at 2GHz
- +23.3dBm output P1dB at 2GHz
- Single 5V supply voltage
- IDD = 150mA
- 50Ω single-ended input / output impedances
- 1.8V and 3.3V logic support
- Standby Mode for power savings
- Operating temperature (TCASE) range: -40°C to +105°C
- 4 × 4 mm, 24-TQFN package
Specifications
- Part Number:F1431
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
90 In Stock |
| 1 | $5.62 | | 10 | $5.06 | | 100 | $4.21 | | 1000+ | $3.55 |
|
|
|
|
Renesas
|
Amplifier, Variable Gain, 30 to 160 MHz, 19.4 dBm, 21.7 dB, 2.2 dB NF, Low-Noise Digital IF VGA with FlatNoise |
More Info
| 1 | $9.32 | | 10 | $8.65 | | 100 | $7.92 | | 1000+ | $7.15 |
Low-noise Digital IF VGA with FlatNoise™ The IDT F1200 low noise digital IF VGA featuring FlatNoise™ technology is ideal for commercial radio systems with very high SNR requirements. Its extremely low distortion makes the device very flexible, while the 200 ohm differential input and output impedances allow it to integrate seamlessly into the signal path. Features - 22 dB GMAX
- 23 dB gain control range
- 7 bit parallel control
- 0.25 dB Gain Steps
- Excellent Noise Figure < 3.0 dB
- 5mm x 5mm 28 pin package
- 200 ohm Differential Input
- 200 ohm Differential Output
- NF degrades < 2dB @ 12dB reduced gain
- 30 MHz - 150 MHz frequency range (for low distortion)
- Ultra-Linear: IP3O +48 dBm typical
- External current setting resistor
- Fast Gain Step Settling < 20 nse
Specifications
- Part Number:F1200
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
100 In Stock |
| 1 | $9.32 | | 10 | $8.65 | | 100 | $7.92 | | 1000+ | $7.15 |
|
|
|
|
Renesas
|
Amplifier, Variable Gain, 0.6 to 2.7GHz, 20.2dBm, 11.6dB Gain, 6x6mm |
More Info
F0440 Dual RF DVGA provides two independent receiver paths each with 11.6dB typical maximum gain and 4.7dB noise figure in the lowband configuration designed to operate with a single +5V supply. For each path Gain control is split into 3 separate attenuators; DSA0 is a single 6dB step using a single control pin, DSA1 includes 23dB SPI-controlled gain adjustment in 1dB steps, and DSA2 includes 18dB attenuation in 6dB steps controlled using two control pins. F0440 offers +40dBm nominal output IP3 using 245mA total ICC. This device is packaged in a 6 x 6 mm, 36-pin TQFN with 50Ω single-ended RF input and RF output impedances for ease of integration into the signal-path lineup for each of the two paths. - Dual Path RF amp and DSAs for Diversity / MIMO Receivers
- RF: 400MHz to 2700MHz
- < 2dB overshoot between DSA transitions
- 11.6dB typical max gain at 900MHz
- DSA0 is a single 6dB coarse step
- DSA1 has 23dB total gain range in 1dB steps
- DSA2 has 18dB gain range in 6dB steps
- +41dBm OIP3 at 2000MHz
- 4.7dB Noise Figure at 900MHz
- +5V supply voltage
- ICC = 245mA
- Independent standby: 7mA standby current
- SPI interface for DSA1
- 1-bit control for DSA0
- -bit control for DSA2
- 50Ω input and output impedance
- Broadband, internally matched
- 6 x 6 mm, 36-pin TQFN package
Specifications
- Part Number:F0440
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
VGA, 1.3-2.8GHz, 4 chl. Att Range 31.5dB, Gain 27.5dB, 3.3V, 8x8,56-Pin |
More Info
DIFF-In / SE-Out Quad Path TX DVGA - 1300MHz to 2800MHz
The F4482 is a 1300MHz to 2800MHz Quad Path TX DVGA outfitted with 100Ω differential inputs and 50Ω single-ended outputs. The device is part of a complete family of VGAs targeting FDD and TDD applications within the 400MHz to 4200MHz frequency range.
Using a single 3.3V power supply and only 485mA of ICC, the F4482 provides four independent transmit paths, each with 27.5dB typical maximum gain, +36.8dBm OIP3, +16.5dBm output P1dB, and 5.7dB NF. Each channel includes a glitch-free digital step attenuator that reduces gain by up to 31.5dB in precise 0.5dB steps.
The F4482 is packaged in an 8 × 8 mm 56-LGA, with matched 100Ω differential input and 50Ω single-ended output impedances for ease of integration into the signal path.
Features
- Independent quad channels for FDD TX applications
- 1300MHz to 2800MHz
- 27.5dB typical maximum gain at 2100MHz
- Precise SPI-controlled Glitch-Free™ gain adjustment
- 31.5dB gain range with 0.5dB step size
- 5.7dB NF at 2100MHz
- +36.8dBm OIP3 at 2100MHz
- +16.5dBm output P1dB at 2100MHz
- 3.3V supply voltage
- ICC = 485mA
- 100Ω differential input impedances
- 50Ω single-ended output impedances
- 1.8V and 3.3V logic support
- Independent channel standby modes for power savings
- Operating temperature (TEP) range: -40°C to +115°C
- 8 × 8 mm, 56-LGA package
Specifications
- Part Number:F4482
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Front-end Module, Switch / LNA DVGA - 3.3GHz to 4.0GHz, 35dB gain with +23dBm OIP3, +15dBm output P1dB, and 1.35dB noise figure at 3500MHz |
More Info
| 1 | $10.10 | | 25 | $9.47 | | 50 | $8.66 | | 100 | $8.08 |
Front-end Module, Switch / LNA DVGA - 3.3GHz to 4.0GHz, 35dB gain with +23dBm OIP3, +15dBm output P1dB, and 1.35dB noise figure at 3500MHz
Specifications
- Part Number:F0453CLFGK
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
| 1 | $10.10 | | 25 | $9.47 | | 50 | $8.66 | | 100 | $8.08 |
|
|
|
|
Renesas
|
Amplifier, Variable Gain, 3.4 to 3.8GHz, 18dBm, 13dB Gain, 6x6mm |
More Info
Dual Matched Broadband RF DVGA The F0448 is a 3.4GHz to 3.8GHz Dual RF digital variable gain amplifier (DVGA) designed for use in receivers.
This Dual RF DVGA provides two independent receiver paths each with 13dB typical maximum gain and 6dB noise figure designed to operate with a single +5V supply. For each path, gain control is split into 3 separate attenuators; DSA0 a single 6dB step using a single control pin, DSA1 a 23dB SPI-controlled gain adjustment in 1dB steps, and DSA2 includes 18dB attenuation in 6dB steps controlled using two control pins. F0448 offers +37dBm nominal output IP3 using 220mA total ICC. This device is packaged in a 6 x 6 mm, 36-QFN with 50 single-ended RF input and RF output impedances for ease of integration. Features - RF frequency range: 3.4GHz to 3.8GHz§
- Dual path RF amp and DSAs for Diversity / MIMO receivers
- < 2dB overshoot between DSA transitions
- 13dB typical max gain at 3.6GHz
- DSA0: Single 6dB coarse step
- DSA1: 23dB total gain range in 1dB steps
- DSA2: 18dB gain range in 6dB steps
- +37dBm OIP3 at 3.6GHz
- 6dB noise figure at 3.6GHz
- +5V supply voltage
- ICC = 220mA
- Independent standby: 7mA standby current
- SPI interface for DSA1
- 1-bit control for DSA0
- 2-bit control for DSA2
- 50Ω input and output impedance
- Broadband, internally matched
- Temperature range: -40°C to +105°C
- 6 x 6 mm, 36-QFN package
Specifications
- Part Number:F0448
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Variable Gain Amplifier -- 0.4 to 1.1, 28dB, 17dBm, 35dBm, 131mA, 3.3V |
More Info
The F4481 is a 400MHz to 1100MHz Quad Path TX DVGA outfitted with 100Ω differential inputs and 50Ω single-ended outputs. The device is part of a complete family of VGAs targeting FDD and TDD applications within the 400MHz to 4200MHz frequency range. Using a single 3.3V power supply and only 520mA of ICC, the F4481 provides four independent transmit paths, each with 28dB typical maximum gain, +35dBm OIP3, +17dBm output P1dB, and 5.7dB NF. Each channel includes a glitch-free digital step attenuator that reduces gain by up to 31.5dB in precise 0.5dB steps. The F4481 is packaged in an 8 × 8 mm 56-LGA, with matched 100Ω differential input and 50Ω single-ended output impedances for ease of integration into the signal path. - Independent quad channels for FDD TX applications
- 400MHz to 1100MHz
- 28dB typical max gain at 900MHz
- Precise SPI-controlled Glitch-Free™ gain adjustment
- 31.5dB gain range with 0.5dB step size
- 5.7dB NF at 900MHz
- +35dBm OIP3 at 900MHz
- +17dBm output P1dB at 900MHz
- 3.3V supply voltage
- ICC = 524mA
- 100Ω differential input impedances
- 50Ω single-ended output impedances
- 1.8V and 3.3V logic support
- Independent channel standby modes for power savings
- Operating temperature (TEP) range: -40°C to +115°C
- 8 × 8 mm, 56-LGA package
Specifications
- Part Number:F4481
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Variable Gain Amplifier -- 3 to 4, 30.5dB, 21dBm, 38dBm, 205mA |
More Info
DUAL CHANNEL BYPASS RX VGA Single Die solution for dual RX channels
Zero_DistortionTM feature enhances linearity
Glitch_FreeTM gain control minimizes overshoot
Amp1 bypass feature reduces large blockers while maintaining linearity
Minimize Phase shift as gain is reduced
Pinout allows for inter-stage filtering • Dual Path RF amp & DSAs for Diversity / MIMO Receivers
• RF Frequency:
• F1106: 1400MHz to 3000MHz
• F1107: 3000MHz to 4000MHz
• 32dB typical max path gain @ 2000MHz
• Each DSA has 31.5 dB of independent control range
• +39dBm second stage amplifier OIP3
• +21dBm OP1dB
• +5V Supply Voltage
• ICC = 380mA
• Independent path STBY
• 50 Ω input and output impedance
Specifications
- Part Number:F1107
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Variable Gain Amplifier -- 1.4 to 3, 32dB, 20dBm, 39dBm, 195mA |
More Info
DUAL CHANNEL BYPASS RX VGA Single Die solution for dual RX channels
Zero_DistortionTM feature enhances linearity
Glitch_FreeTM gain control minimizes overshoot
Amp1 bypass feature reduces large blockers while maintaining linearity
Minimize Phase shift as gain is reduced
Pinout allows for inter-stage filtering • Dual Path RF amp & DSAs for Diversity / MIMO Receivers
• RF Frequency:
• F1106: 1400MHz to 3000MHz
• F1107: 3000MHz to 4000MHz
• 32dB typical max path gain @ 2000MHz
• Each DSA has 31.5 dB of independent control range
• +39dBm second stage amplifier OIP3
• +21dBm OP1dB
• +5V Supply Voltage
• ICC = 380mA
• Independent path STBY
• 50 Ω input and output impedance
• Extended temperature: -40 °C to +105 °C
• 6mm x 6mm, 36-pin TQFN package
Specifications
- Part Number:F1106
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Amplifier, Digital Variable, 2100 to 2950 MHz, 21.4 dBm, 32.1 dB, 3.9 dB NF, KLin RF Amplifier, DSA and PA driver |
More Info
The F1456 is a High-Gain/High-Linearity 2100MHz to 2950MHz TX Variable Gain Amplifier used in transmitter applications. The F1456 TX VGA provides 32.1dB maximum gain with +38dBm OIP3 and 3.9dB noise figure. Up to 31.5dB gain control is achieved using the combination of a digital step attenuator (DSA) plus KLIN™ RF variable gain amplifier gain adjustment. This device uses a single 5V supply and 215mA of ICC. This device is packaged in a 6 × 6 mm, 28-QFN with 50Ω single-ended RF input and RF output impedances for ease of integration into the signal path. - Broadband 2100MHz to 2950MHz
- 32.1dB max gain
- 3.9dB NF @ max gain (2650MHz)
- 31.5dB total gain control range, 0.5dB step
- < 2 dB overshoot between major gain transitions
- +38dBm OIP3
- Maintains +21.5dBm output P1dB over 13dB gain adjustment range
- SPI interface for DSA control
- Single 5V supply voltage
- ICC = 215mA
- Up to +105 °C TCASE operating temperature
- 50Ω input and output impedance
- Standby for power savings
- Pin compatible 700–1100MHz and 1400–2300MHz versions
- 6 × 6 mm, 28-QFN package
Specifications
- Part Number:F1456
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Amplifier, Digital Variable, 1400 to 2300 MHz, 23 dBm, 32.8 dB, 3.9 dB NF, KLin RF Amplifier, DSA and PA driver |
More Info
The F1455 is a High-Gain / High-Linearity 1400MHz to 2300MHz TX Variable Gain Amplifier used in transmitter applications. The F1455 TX VGA provides 32dB maximum gain with +39dBm OIP3 and 4dB noise figure. Up to 29.5dB gain control is achieved using the combination of a digital step attenuator (DSA) plus KLIN™ RF variable gain amplifier gain adjustment. This device uses a single 5V supply and 216mA of ICC. This device is packaged in a 6 x 6 mm, 28-QFN with 50Ω single-ended RF input and RF output impedances for ease of integration into the signal path. - Broadband 1400MHz to 2300MHz
- 32dB max gain
- 4dB NF at max gain (2000MHz)
- KLIN™ amplifier with 6dB gain range
- DSA: 23.5dB range
- 29.5dB total gain control range, 0.5dB step
- < 2 dB overshoot between major gain transitions such as 15.5dB to 16dB atten
- +40dBm OIP3
- Maintains +23.5dBm output P1dB over first 6dB gain adjustment range
- SPI interface for DSA control
- Single 5V supply voltage
- ICC = 216mA
- Up to +105°C TCASE operating temperature
- 50Ω input and output impedance
- Standby for power savings
- Pin compatible 700MHz and 2700MHz versions
- 6 x 6 mm, 28-QFN package
Specifications
- Part Number:F1455NKGK8
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Amplifier, Digital Variable, 700 to 1000 MHz, 23 dBm, 32 dB, 6x6mm, QFN,KLIN RF Amplifier, DSA and PA driver |
More Info
Amplifier, Digital Variable, 700 to 1000 MHz, 23 dBm, 32 dB, 6x6mm, QFN,KLIN RF Amplifier, DSA and PA driver
Specifications
- Part Number:F1451NKGK8
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
|
|
Renesas
|
Amplifier, Low-noise Dual IF VGA with FlatNoise, 10 to 500 MHz, 19.7 dBm, 20 dB, 31.5 dB gain control range, Low-noise Dual IF VGA with FlatNoise |
More Info
The Renesas F1240 IF VGA featuring FlatNoise™ technology improves system SNR, especially at lower gain settings. By keeping both IP3O & NF flat while gain is backed off, the system SNR is improved significantly under high level interferer conditions, especially when considering alias noise in an IF sampling receiver. The fast-settling, parallel mode gain step of 0.50 dB coupled with the excellent differential non-linearity allow for SNR to be maximized further by targeting the minimum necessary gain in small, accurate increments. The matched output does not require a terminating resistor, thus the gain and distortion performance are preserved when driving Bandpass Anti-Alias filters. - Ideal for systems with high SNR requirements
- 20 dB typical Maximum Gain
- 31 dB gain control range
- 6 bit control
- 0.50 dB Gain Steps
- Excellent Noise Figure ~ 4.0 dB
- 5mm x 5mm 32 pin package
- 200 ohm Differential Matched Input
- 200 ohm Differential Matched Output
- No termination resistor required
- NF degrades < 2dB @ 10 dB reduced gain
- 10 MHz – 500 MHz frequency range
- Ultra-Linear: IP3O +47 dBm typical
- Excellent 2nd Harmonic Rejection
- Parallel / Serial Control
- External current setting resistors
- Very fast settling < 15 nsec
- Individual Power Down Modes
- Extremely low power consumption: 79 mA / Ch
Specifications
- Part Number:F1240
- Manufacturer:Renesas Electronics America Inc.
- Status:Standard
|
|
Submit Quote Request |
Submit Quote Request
|
|
